Jai AD-081GE Manuel d'utilisateur

1002E-0912 AD-081GE Digital 2CCD Progressive Scan HDR / High Frame Rate Camera Document Version: Ver.1.1 AD-081GE

AD-081GE 9 5. Pin configuration 5.1. 12-pin Multi-connector (DC-in/GPIO/Iris Video) Type: HR10A-10R-12PB (Hirose) male. (Seen from the rea

AD-081GE 10 5.4. DIP switches DIP switches are located inside the camera. When the top cover is removed, please pay careful attention so t

AD-081GE 11 Fig.6 Trigger circuit 6. Input and output circuits In the following schematic diagrams the input and output circuits for video and t

AD-081GE 12 7. System Configuration 7.1. System connection When the AD-081GE is connected to a PC, there are two connection methods. Method

AD-081GE 13 8. GPIO (Inputs and outputs) 8.1. Overview All input and output signals pass through the GPIO (General Purpose Input and Out

AD-081GE 14 8.1.1 LUT (Cross Point Switch) The LUT works as a cross-point switch which allows connecting inputs and outputs freely. The signals

AD-081GE 15 8.1.5 Recommended External Input circuit diagram for customer Fig.11 External Input Circuit、OPT IN 1 and 2 8.1.6 Recommen

AD-081GE 16 8.1.7 Optical Interface Specifications The relation of the input signal and the output signal through the optical interface is as fol

AD-081GE 17 8.2. Inputs and outputs table Output Ports Trig. 1-0 Trig. 1-1 Trig. 2-0 Trig. 2-1 OPT OUT1 OPT OUT2 TTL OUT1 Time Stamp Reset 1 Seq. Re

AD-081GE 18 8.3. Configuring the GPIO module (register settings) 8.3.1 Input /Output Signal Selector GPIO is used to determine whic

AD-081GE 2 Notice The material contained in this manual consists of information that is proprietary to JAI Ltd., Japan and may only be used by

AD-081GE 19 Start PointEnd PointLengthStart PointEnd PointLength8.3.3 Pulse generators (20 bit x 4) There are 4 pulse generators (designated 0 throu

AD-081GE 20 8.4. GPIO programming examples 8.4.1 GPIO Plus PWC shutter Example: 20µs unit pulse width exposure control (PWC). Pixe

AD-081GE 21 8.4.2 Internal Trigger Generator Example: Create a trigger signal and trigger the camera. These are the settings for Imager 1. For

AD-081GE 22 Analog Signal [mV]Black Level102389032025700Digital Out [LSB]White Clip Level100% Level8009. GigE Vision® Streaming Protocol (GVSP) 9

AD-081GE 23 9.2.3 GVSP_PIX_MONO10_PACKED (10 bit) 1 Byte 2 Byte 3 Byte

AD-081GE 24 10. Functions and Operations 10.1. GigE Vision Standard Interface The AD-081GE is designed in accordance with the GigE Vision st

AD-081GE 25 Minimum PC requirements are as follows in order to fulfill the above conditions:  Intel Core 2 Duo , 2.4 GHz or better  At least 2 G

AD-081GE 26 Regarding data transfer rate, a larger packet size produces a slightly lower data transfer rate. AD-081GE can support a maximum of 16020 b

AD-081GE 27 10.2.3 Disable Firewalls To ensure proper functions of the JAI SDK & Control Tool, all firewalls must be disabled. This also includ

AD-081GE 28 (6) Expand [Network adapters]. (7) Select target NIC, right-click, and click [Properties]. Note: Intel 1000 is used in this example. If

AD-081GE Supplement The following statement is related to the regulation on “ Measures for the Administration of the control of Pollution by Electro

AD-081GE 29 (9) Select Jumbo Frames property, and select 16128 under Value. (10)Click [OK]. (11)Close [Device Manager]. (12)Close [System Propertie

AD-081GE 30 10.2.6 Interrupt Moderation rate If the Network Connection Properties list contains a property called Interrupt Moderation Rate, th

AD-081GE 31 1. Type in the frame rate of the connected camera. AD-081GE operates at 30 fps. 2. Set the bandwidth at 80%. 3. Click the cal

AD-081GE 32  If it is not shown, confirm the setting in the “Settings” window. Access the “Settings” window by clicking on the “Settings Tab” icon.

AD-081GE 33 10.3. Basic functions The AD-081GE is based on a beam-splitter prism, allowing precise separation into two separate monochrome channels

AD-081GE 34 10.3.3 High frame rate mode (Double speed) In this mode, double speed readout (60fps) can be achieved by shifting the exposure timing fo

AD-081GE 35 BW1BW2Video outputVideo outputIncoming lightIncoming lightVideo outputIncoming lightComposed videoBW-1BW-2100%100%100% Fig.19 Compo

AD-081GE 36  High dynamic range ( Sync Mode 6) In this mode, a roughly proportional approach is used which places an emphasis on the image from the

AD-081GE 37 10.3.5 High S/N mode In this mode, each sensor output is synchronized and has the same exposure time. The image average of the two sign

AD-081GE 38 10.3.7 Iris Video output The lens-iris video output level at pin 4 of the 12-pin Hirose connector is 700 mV for 100% video output level.

AD-081GE 3 Table of Contents 1. General ... 6 2.

AD-081GE 39 The variable scan readout is connected with the ROI settings. 1. If ROI is set, these settings are applied to the partial scan settings. 2

AD-081GE 40 OB period in the upper part of the frame 3L Fast dump period for the upper part = (4+3+193 -1) ÷4 +1 = 49.75 + 1 = 50.7

AD-081GE 41 ◆ Exposure Time Abs (GenICam Standard) This is a function specified in the GenICam standard. The shutter speed can be entered as an absol

AD-081GE 42 10.3.13 Knee compensation If the relation of input and output is linear (1:1), the output level will be clipped at a certain input leve

AD-081GE 43 10.3.16 Rear Panel Indicator The rear panel mounted LED provides the following information: Power LED:  Amber : Power connected –

AD-081GE 44 10.4. Sensor Layout and Timing 10.4.1 Sensor Layout The CCD sensor layout, with respect to vertical and horizontal pixels used i

AD-081GE 45 10.4.2 Horizontal Timing The horizontal timing for Continuous mode, full frame and partial scan is shown below. DATA OUTD V A LCC D

AD-081GE 46 10.4.3 Vertical Timing The vertical timing for Continuous mode and full frame scan is shown below. 2 L6L4 L7 L5 L7 6 8 LEff ecti ve

AD-081GE 47 10.4.4 Partial Scan (when the start line is set at 193rd) The following chart shows the vertical timing for 1/2 height partial scanni

AD-081GE 48 10.4.5 Vertical binning Vertical binning combines charge from two adjacent lines, reducing the vertical resolution to half and at the

AD-081GE 4 10.2.3 Disable Firewalls ...27 10.2.4 Enabling Jumbo Frame ..

AD-081GE 49 10.5. Operation Mode AD-081GE has the following 8 operation modes and OB transfer and ROI modes. 1 Continuous Pre-selected exposure

AD-081GE 50 10.5.2 Edge Pre-Select (EPS) trigger mode An external trigger pulse initiates the capture, and the exposure time (accumulation time)

AD-081GE 51 Exposur e Del ay(Exposure)DATA outData out Del ay1 to 2L13 to 14LExt. Tri gFVALEENLVALExposure Pri od1L = 1420cl ock ( 42.07us)14.2us Fig

AD-081GE 52 10.5.3 Pulse Width Control (PWC) trigger mode In this mode the accumulation time is equal to the trigger pulse width. Here it is poss

AD-081GE 53 On PWC mode, when “Smearless ON ” is selected, the actual accumulation time is “the trigger pulse width” – “Smearless active period (1

AD-081GE 54 10.5.4 Reset Continuous Trigger (RCT) mode The RCT mode operates like EPS (edge preselect) mode with smearless function. An external t

AD-081GE 55 10.5.5 Particle Image Velocimetry PIV mode is an independent function and is not to be combined with the High Frame Rate function, th

AD-081GE 56 10.5.6 Sequential Trigger Mode (EPS) This mode allows the user to define a preset sequence of up to 10 images, each with its own RO

AD-081GE 57 Important Notes:  When this mode is used, at first set the video sending flag to OFF (Acquisition end). Then set the trigger mode to “

AD-081GE 58 In PWC mode, when “Smearless ON ” is selected, the actual accumulation time is the trigger pulse width minus the Smearless active period

AD-081GE 5 12. Specifications ...64 12.1. Spectral response .

AD-081GE 59 10.5.9 Optical Black transfer mode It is possible for the user to decide whether the optical black (OB) portion of the image will be

AD-081GE 60 10.6. Operation Mode and Functions matrix 10.6.1 Readout Mode (0xA098) 0:SYNC Sensor BW-1 BW-2 Auto Iris output (Note2) Tri

AD-081GE 61 10.6.2 Readout mode (0xA098) 1:ASYNC Sensor BW-1 BW-2 Auto Iris output (note2) Trigger Input Trigger 1 : Valid Trigger 2 :

AD-081GE 62 10.7. Special note for settings 10.7.1 When the image size is changed When the image size needs to be changed while the image is being

AD-081GE 63 11. External Appearance and Dimensions 1 8 81G PIO D C I N / T RI GPO W E RTRIG G ERGig E-2Gig E-14055405540C Mount4-M3 Dept h5404-M3

AD-081GE 64 12. Specifications 12.1. Spectral response Fig. 53 Spectral response of monochrome sensor Fig. 54 Total

AD-081GE 65 12.2. Specifications Table Specifications AD-081GE Scanning system Progressive scan Frame Rate Full scan 30.0 frames / sec. Progre

AD-081GE 66 Storage temperature/humidity -25C to +60C / 20% to 80% (non-condensing) Vibration 3G (15Hz to 200Hz XYZ ) Shock 50G Regulatory CE (EN610

AD-081GE 67 Register Map The table below provides detailed information for the hardware registers used for controlling the camera and obtaining info

AD-081GE 68 0xA520 ROI 2 Offset Y OffsetY2 RW 4 0 – 760 Offset Y2 0 0xA524 ROI 3 Width Width3 RW 4 8 - 1024 Width 3 W.Max 0xA528 ROI 3 Height Height

AD-081GE 6 1. General This manual covers the digital 2-CCD progressive scan camera AD-081GE. The AD-081GE is a GigE Vision® compliant camera, belo

AD-081GE 69 0xA008 Exposure Time Raw ExposureTimeRaw RW 4 0 to 792 (OFF) Flexible setting of exposure time ranging from 20 µs to 33.31 ms using the L

AD-081GE 70 0xA0C8 Auto Gain Value AutoGainValue RO 4 See the gain raw value while AGC is being performed 0xA71C Digital Sensor 2 DigitalSensor2 RW

AD-081GE 71 0xB07C Line Selector Line3-Optical Out 2 Line3 RW 4 Bit24:Line Inverter 0=False (Active High) 1=True(Active Low) 2:LVAL2 3:DVAL1 4:DVAL2 5

AD-081GE 72 0xB02C Clear Mode for the Pulse Generator 1 PulseGeneratorClear1 RW 4 0 :Free Run 1:High Level 2: Low Level 4: Rising Edge 8: Falling Edge

AD-081GE 73 Sequence Acquisition Mode Address Display Name (JAI Control Tool) GenICam name Read / Write Size Value / Range of value Description Defaul

AD-081GE 74 Support DHCP GevSupportedConfigurationDHCP Bit 29: LLA 0. DHCP and LLA bits must be on. Support Persistent IP GevSupportedConfigurationPer

AD-081GE 75 0x0944 Timestamp control Latch GevTimestampcontrolLatch W 4 Command 2 This register holds the least significant bytes. Used to latch the c

AD-081GE 76 LUT Controls Address Display Name (JAI Control Tool) GenICam name Read / Write Size Value / Range of value Description Default value 0xA2

AD-081GE 77 Appendix 1. Precautions Personnel not trained in dealing with similar electronic devices should not service this camera. The camer

AD-081GE 78 4. Caution when mounting the camera When you mount the camera on your system, please make sure to use screws of the recomm

AD-081GE 7 3. Main Features  C3 Advanced series progressive scan camera  GigE Vision, GenICam compliant  2-channel monochrome CCDs are empl

AD-081GE 79 Index A asynchronous ... 7, 36, 49 Auto-detect LVAL ... 36 B Bit Allocation...

AD-081GE 80 Change History Month/Year Revision Changes Oct 2009 1.0 New release Dec 2009 1.1 Add functions, high dynamic range mode 5 and 6. Modify

AD-081GE 81 User's Record Camera type: AD-081GE Revision: …………….. Serial No. …………….. Firmware version. …………….. For camera revisi

AD-081GE 8 4. Locations and functions  CCD sensor : 1/3 inch CCD sensor  Lens Mount : C-mount ( Note*1 )  12P Multi C